{"title":"Real Wood Veneer Edging Rolls","description":"\u003ch2\u003eReal Wood Veneer Edging Rolls\u003c\/h2\u003e\n\u003cp\u003eExplore real wood veneer edging rolls for finishing exposed furniture, cabinet and interior joinery edges. These flexible veneer rolls are selected by width, length and timber appearance for the job in hand.\u003c\/p\u003e\n\u003ch3\u003eChoosing Veneer Edging\u003c\/h3\u003e\n\u003cp\u003eCheck each product page for its exact width, roll length, veneer format and adhesive information. Choose a width that allows the finished edge to be trimmed cleanly, and consider grain direction and colour variation when planning adjoining pieces.\u003c\/p\u003e\n\u003ch3\u003ePreparation and Application\u003c\/h3\u003e\n\u003cp\u003ePrepare the receiving edge so it is clean, dry, smooth and stable. The suitable adhesive and application method depend on the individual veneer, substrate and intended interior use, so check the product details and adhesive manufacturer’s instructions before bonding.\u003c\/p\u003e\n\u003cp\u003eTest the complete veneer, adhesive, substrate and finishing system on an offcut first. After application, trim carefully and finish the edge as required for the project.\u003c\/p\u003e\n\u003ch3\u003eNatural Wood Variation\u003c\/h3\u003e\n\u003cp\u003eReal wood veneer varies naturally in colour, grain, figuring and marking. Product images are representative, and pieces from different rolls may not be identical.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003ch3\u003eWhat is real wood veneer edging used for?\u003c\/h3\u003e\n\u003cp\u003eIt is used to finish exposed edges on furniture, cabinet panels, shelves, interior joinery and repair work where the selected veneer and bonding system are suitable.\u003c\/p\u003e\n\u003ch3\u003eHow do I choose the right roll?\u003c\/h3\u003e\n\u003cp\u003eCompare the product’s timber appearance, width and roll length with the edge being finished. Also check whether the product is supplied with or without adhesive before ordering.\u003c\/p\u003e\n\u003ch3\u003eDoes real wood veneer vary in appearance?\u003c\/h3\u003e\n\u003cp\u003eYes. Natural wood varies in shade, grain and figuring. Plan the layout before application when a close visual match matters.\u003c\/p\u003e\n\u003ch3\u003eRelated Veneer Collections\u003c\/h3\u003e\n\u003cp\u003eFor pre-glued, heat-activated edging, visit \u003ca href=\"\/collections\/iron-on-veneer-edging\"\u003eiron-on veneer edging\u003c\/a\u003e. For edging supplied without pre-applied adhesive, browse \u003ca href=\"\/collections\/unglued-veneer-edging\"\u003eunglued veneer edging\u003c\/a\u003e. For large-format sheets, see \u003ca href=\"\/collections\/flexible-wood-veneer-sheets\"\u003eflexible wood veneer sheets\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"anigre-fshm-flexible-wood-veneer-25mm-x-100m","title":"Anigre Flexible Wood Veneer FSHM 25mm x 100m","description":"\u003ch2\u003eAnigre Flexible Wood Veneer FSHM 25mm x 100m\u003c\/h2\u003e\u003cp\u003eAnigre Flexible Wood Veneer FSHM 25mm x 100m is a decorative real wood veneer roll designed for cabinet edging, furniture repairs, shelving, doors, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eAnigre is known for its pale golden to light brown appearance and clean, attractive grain. It is often chosen for furniture, interior panels, cabinetry and decorative joinery where a lighter timber finish is required. Its warm natural tone makes it suitable for both modern and traditional furniture designs.\u003c\/p\u003e\u003cp\u003eThe 25mm width makes this veneer ideal for board edging, cabinet parts, shelving edges, drawer fronts, door edges, trims and repair sections. Supplied in a longer 100m roll, it is well suited to workshop use, repeat edging work and production applications where a continuous veneer strip is needed.\u003c\/p\u003e\u003cp\u003eThis flexible anigre veneer can be used to upgrade plain board edges, match existing light timber finishes, repair worn edging or add a real wood appearance to panels and fitted furniture.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural anigre colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Anigre FSHM 25mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for cabinet edging, furniture repairs, shelving edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is Anigre veneer?\u003c\/h4\u003e\u003cp\u003eAnigre usually has a pale golden to light brown appearance, giving a clean and warm natural timber finish.\u003c\/p\u003e\u003ch4\u003eIs the 25mm width suitable for cabinet edging?\u003c\/h4\u003e\u003cp\u003eYes. The 25mm width is suitable for board edges, shelves, doors, drawer fronts and cabinet parts.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural anigre colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 25mm wide x 100m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light timber furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800110429,"sku":"VEN025A","price":23.2,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN025A_abaf8f21-97f2-41db-ac71-9168664807ad.jpg?v=1781946281"},{"product_id":"anigre-fshm-flexible-wood-veneer-50mm-x-100m","title":"Anigre Flexible Wood Veneer FSHM 50mm x 100m","description":"\u003ch2\u003eAnigre Flexible Wood Veneer FSHM 50mm x 100m\u003c\/h2\u003e\u003cp\u003eAnigre Flexible Wood Veneer FSHM 50mm x 100m is a decorative real wood veneer roll designed for wider cabinet edging, furniture repairs, shelving, doors, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eAnigre is valued for its pale golden to light brown appearance, even tone and attractive natural grain. It is often used for furniture, interior panels, cabinetry and decorative joinery where a lighter timber finish is required. Its warm, clean appearance works well in both modern and traditional furniture designs.\u003c\/p\u003e\u003cp\u003eThe 50mm width makes this veneer suitable for wider board edges, cabinet parts, shelving edges, drawer fronts, door edges, trims and repair sections where more coverage is needed. Supplied in a longer 100m roll, it is ideal for workshop use, repeated edging work and production applications.\u003c\/p\u003e\u003cp\u003eThis flexible anigre veneer can be used to upgrade plain board edges, match existing light timber finishes, repair worn edging or add a real wood appearance to panels and fitted furniture.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural anigre colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Anigre FSHM 50mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for wider cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is Anigre veneer?\u003c\/h4\u003e\u003cp\u003eAnigre usually has a pale golden to light brown appearance, giving a clean and warm natural timber finish.\u003c\/p\u003e\u003ch4\u003eIs the 50mm width suitable for wider board edges?\u003c\/h4\u003e\u003cp\u003eYes. The 50mm width is suitable for wider board edges, shelves, doors, drawer fronts and cabinet parts where extra coverage is required.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural anigre colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 50mm wide x 100m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light timber furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800372573,"sku":"VEN025B","price":34.23,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN025B_f1ff856b-ed48-4716-9c31-89fc26dbc10b.jpg?v=1781946892"},{"product_id":"ash-fshm-flexible-wood-veneer-25mm-x-100m","title":"VENEER FSHM ASH 25x100m","description":"\u003ch2\u003eAsh Flexible Wood Veneer FSHM 25mm x 100m\u003c\/h2\u003e\u003cp\u003eAsh Flexible Wood Veneer FSHM 25mm x 100m is a decorative real wood veneer roll designed for cabinet edging, furniture repairs, shelving, doors, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eAsh is valued for its light natural colour, strong grain pattern and clean hardwood appearance. It is a popular choice for furniture, cabinetry, panels and interior joinery where a pale timber finish with visible character is required. Its fresh, contemporary look makes it suitable for both modern furniture and traditional woodworking projects.\u003c\/p\u003e\u003cp\u003eThe 25mm width makes this veneer ideal for board edging, cabinet parts, shelving edges, drawer fronts, door edges, trims and repair sections. Supplied in a longer 100m roll, it is well suited to workshop use, repeat edging work and production applications where a continuous ash veneer strip is needed.\u003c\/p\u003e\u003cp\u003eThis flexible ash veneer can be used to upgrade plain board edges, match existing ash or light timber finishes, repair worn edging or add a real wood appearance to panels and fitted furniture.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Ash FSHM 25mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for cabinet edging, furniture repairs, shelving edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is ash veneer?\u003c\/h4\u003e\u003cp\u003eAsh veneer usually has a pale cream to light brown appearance with a visible, attractive grain pattern.\u003c\/p\u003e\u003ch4\u003eIs the 25mm width suitable for cabinet edging?\u003c\/h4\u003e\u003cp\u003eYes. The 25mm width is suitable for board edges, shelves, doors, drawer fronts and cabinet parts.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 25mm wide x 100m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light timber furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800438109,"sku":"VEN026A","price":29.73,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN026A.jpg?v=1789189267"},{"product_id":"ash-fshm-flexible-wood-veneer-50mm-x-100m","title":"VENEER FSHM ASH 50x100m","description":"\u003ch2\u003eAsh Flexible Wood Veneer FSHM 50mm x 100m\u003c\/h2\u003e\u003cp\u003eAsh Flexible Wood Veneer FSHM 50mm x 100m is a decorative real wood veneer roll designed for wider cabinet edging, furniture repairs, shelving, doors, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eAsh is valued for its light natural colour, strong grain pattern and clean hardwood appearance. It is a popular choice for furniture, cabinetry, panels and interior joinery where a pale timber finish with visible character is required. Its fresh, contemporary look makes it suitable for both modern furniture and traditional woodworking projects.\u003c\/p\u003e\u003cp\u003eThe 50mm width provides broader coverage, making it suitable for wider board edges, worktop edges, cabinet carcasses, furniture panels and surface work where a wider veneer strip is needed. Supplied in a 100m roll, it is ideal for workshop and production use where high volumes of edging are required from a single roll.\u003c\/p\u003e\u003cp\u003eThis flexible ash veneer can be used to upgrade plain board edges, match existing ash or light timber finishes, repair worn edging or add a real wood appearance to panels and fitted furniture.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Ash FSHM 50mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for wider cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is ash veneer?\u003c\/h4\u003e\u003cp\u003eAsh veneer usually has a pale cream to light brown appearance with a visible, attractive grain pattern.\u003c\/p\u003e\u003ch4\u003eIs the 50mm width suitable for wider board edges?\u003c\/h4\u003e\u003cp\u003eYes. The 50mm width is suitable for wider board edges, worktops, shelves, cabinet carcasses, doors and furniture panels.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 50mm wide x 100m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light timber furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800536413,"sku":"VEN026B","price":34.23,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN026B.jpg?v=1784618598"},{"product_id":"ash-fs-unglued-flexible-wood-veneer-30mm-x-100m","title":"VENEER FSHM ASH 30x100m UNGLUED","description":"\u003ch2\u003eAsh Flexible Wood Veneer FS Unglued 30mm x 100m\u003c\/h2\u003e\u003cp\u003eAsh Flexible Wood Veneer FS Unglued 30mm x 100m is a decorative real wood veneer roll designed for cabinet edging, furniture repairs, shelving, door edges, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eAsh is valued for its pale natural colour, visible grain and clean hardwood appearance. It is commonly used in furniture, cabinetry, panels and interior joinery where a light timber finish with attractive grain character is required.\u003c\/p\u003e\u003cp\u003eThe 30mm width makes this veneer suitable for wider board edges, cabinet parts, shelf edges, drawer fronts, door edges, trims and repair sections where more coverage is needed. Supplied in a 100m roll, it is practical for workshop use, repeated edging work and production applications.\u003c\/p\u003e\u003cp\u003eThis veneer is supplied \u003cstrong\u003eunglued\u003c\/strong\u003e — the back is fleeced for flexibility and the front face is sanded smooth, but no adhesive has been applied to the reverse. This gives you full control to choose the most suitable bonding method for your substrate and process, whether that is contact adhesive, PVA, specialist veneer glue or press bonding.\u003c\/p\u003e\u003cp\u003eIt can be used to upgrade plain board edges, match existing ash or light timber finishes, repair worn edging or add a real wood appearance to fitted furniture and decorative panels.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FS Mean?\u003c\/h3\u003e\u003cp\u003eFS stands for \u003cstrong\u003eFleeced and Sanded\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, and the front face is sanded to a smooth, consistent finish. This product is supplied \u003cstrong\u003eunglued\u003c\/strong\u003e — no hot melt or pre-applied adhesive is on the reverse. When trimming after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e, giving a clean, controlled finish.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Ash FS Unglued 30mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat does unglued veneer mean?\u003c\/h4\u003e\u003cp\u003eUnglued veneer does not have a pre-applied adhesive backing. You apply your own adhesive — such as contact adhesive, PVA or specialist veneer glue — to suit your process and substrate.\u003c\/p\u003e\u003ch4\u003eIs the 30mm width suitable for wider board edges?\u003c\/h4\u003e\u003cp\u003eYes. The 30mm width is suitable for wider board edges, shelves, doors, drawer fronts and cabinet parts where extra coverage is required.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural ash colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 30mm wide x 100m long flexible ash wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light timber furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"SMC WHOLESALE","offers":[{"title":"Default Title","offer_id":62849800569181,"sku":"VEN026C","price":30.42,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN026C.jpg?v=1784618598"},{"product_id":"white-beech-fshm-flexible-wood-veneer-25mm-x-100m","title":"White Beech Flexible Wood Veneer FSHM 25mm x 100m","description":"\u003ch2\u003eWhite Beech Flexible Wood Veneer FSHM 25mm x 100m\u003c\/h2\u003e\u003cp\u003eWhite Beech Flexible Wood Veneer FSHM 25mm x 100m is a decorative real wood veneer roll designed for cabinet edging, furniture repairs, shelving, door edges, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eWhite beech is valued for its pale, clean timber appearance and smooth, even grain. It is often used in furniture, cabinetry, panels and interior joinery where a light natural wood finish is required. Its neutral tone makes it suitable for both modern furniture and traditional woodworking projects.\u003c\/p\u003e\u003cp\u003eThe 25mm width makes this veneer ideal for board edging, cabinet parts, shelf edges, drawer fronts, door edges, trims and repair sections. Supplied in a 100m roll, it is practical for workshop use, repeated edging work and production applications where a continuous beech veneer strip is required.\u003c\/p\u003e\u003cp\u003eThis flexible white beech veneer can be used to upgrade plain board edges, match existing beech or light timber finishes, repair worn edging or add a real wood appearance to fitted furniture and decorative panels.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural white beech colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is White Beech FSHM 25mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is white beech veneer?\u003c\/h4\u003e\u003cp\u003eWhite beech veneer has a pale, clean timber appearance with a smooth, subtle natural grain.\u003c\/p\u003e\u003ch4\u003eIs the 25mm width suitable for cabinet edging?\u003c\/h4\u003e\u003cp\u003eYes. The 25mm width is suitable for board edges, shelves, doors, drawer fronts and cabinet parts.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural white beech colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 25mm wide x 100m long flexible white beech wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light beech furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800601949,"sku":"VEN027A","price":15.89,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN027A.jpg?v=1781948728"},{"product_id":"white-beech-fshm-flexible-wood-veneer-50mm-x-100m","title":"White Beech Flexible Wood Veneer FSHM 50mm x 100m","description":"\u003ch2\u003eWhite Beech Flexible Wood Veneer FSHM 50mm x 100m\u003c\/h2\u003e\u003cp\u003eWhite Beech Flexible Wood Veneer FSHM 50mm x 100m is a decorative real wood veneer roll designed for wider cabinet edging, furniture repairs, shelving, door edges, trims and detailed joinery work.\u003c\/p\u003e\u003cp\u003eWhite beech is valued for its pale, clean timber appearance and smooth, even grain. It is often used in furniture, cabinetry, panels and interior joinery where a light natural wood finish is required. Its neutral tone makes it suitable for both modern furniture and traditional woodworking projects.\u003c\/p\u003e\u003cp\u003eThe 50mm width provides broader coverage, making it suitable for wider board edges, worktop edges, cabinet carcasses, furniture panels and surface work where a wider veneer strip is needed. Supplied in a 100m roll, it is ideal for workshop and production use where high volumes of edging are required from a single roll.\u003c\/p\u003e\u003cp\u003eThis flexible white beech veneer can be used to upgrade plain board edges, match existing beech or light timber finishes, repair worn edging or add a real wood appearance to fitted furniture and decorative panels.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, shopfitting, display units, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural white beech colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is White Beech FSHM 50mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for wider cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is white beech veneer?\u003c\/h4\u003e\u003cp\u003eWhite beech veneer has a pale, clean timber appearance with a smooth, subtle natural grain.\u003c\/p\u003e\u003ch4\u003eIs the 50mm width suitable for wider board edges?\u003c\/h4\u003e\u003cp\u003eYes. The 50mm width is suitable for wider board edges, worktops, shelves, cabinet carcasses, doors and furniture panels.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural white beech colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 50mm wide x 100m long flexible white beech wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve light beech furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800634717,"sku":"VEN027B","price":32.29,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN027B_c337db94-401a-41fc-88b5-45585ad65e5a.jpg?v=1781949495"},{"product_id":"beech-fshm-flexible-wood-veneer-30mm-x-100m","title":"Beech Flexible Wood Veneer FSHM 30mm x 100m","description":"\u003ch2\u003eBeech Flexible Wood Veneer FSHM 30mm x 100m\u003c\/h2\u003e\u003cp\u003eBeech Flexible Wood Veneer FSHM 30mm x 100m is a practical decorative veneer roll for furniture makers, cabinet makers, joiners and shopfitters who need a clean, warm timber finish for panels, edges, repairs and bespoke interior work.\u003c\/p\u003e\u003cp\u003eBeech is one of the most widely used European hardwoods in furniture and joinery. It has a pale pinkish-brown to light tan colour with a fine, even grain and smooth texture. It is a popular choice for fitted furniture, cabinetry, shelving and interior joinery where a consistent, attractive hardwood finish is required.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003cp\u003eThe 30mm width provides good coverage for a wide range of board edges, cabinet parts, shelving edges, drawer fronts and door edges. Supplied in a 100m roll, it is ideal for workshop and production use.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, display units, shopfitting, decorative trims and bespoke joinery work.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural beech colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable substrate. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Beech FSHM veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for decorative timber finishing on furniture, cabinet panels, shelving, doors, trims, edging and joinery repair work.\u003c\/p\u003e\u003ch4\u003eWhat colour is beech veneer?\u003c\/h4\u003e\u003cp\u003eBeech veneer has a pale pinkish-brown to light tan colour with a fine, even grain and smooth texture.\u003c\/p\u003e\u003ch4\u003eIs this suitable for cabinet making?\u003c\/h4\u003e\u003cp\u003eYes. Beech veneer is one of the most commonly used veneers in cabinet making, fitted furniture and decorative panel work.\u003c\/p\u003e\u003ch4\u003eWhat does FSHM mean?\u003c\/h4\u003e\u003cp\u003eFSHM stands for Fleeced, Sanded and Hot Melt. The back is fleeced for flexibility, the front face is sanded smooth, and a hot melt glue backing allows iron-on application. When trimming, the cut follows the blade rather than the grain.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer?\u003c\/h4\u003e\u003cp\u003eThis veneer is supplied as a 30mm wide x 100m long roll.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800700253,"sku":"VEN028A","price":22.17,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN028A_4ed410b8-fa40-4ec7-bc13-f9eb4290ac13.jpg?v=1781945992"},{"product_id":"beech-fshm-flexible-wood-veneer-50mm-x-100m","title":"Beech Flexible Wood Veneer FSHM 50mm x 100m","description":"\u003ch2\u003eBeech Flexible Wood Veneer FSHM 50mm x 100m\u003c\/h2\u003e\u003cp\u003eBeech Flexible Wood Veneer FSHM 50mm x 100m is a practical decorative veneer roll for furniture makers, cabinet makers, joiners and shopfitters who need a clean, warm timber finish for panels, edges, repairs and bespoke interior work.\u003c\/p\u003e\u003cp\u003eBeech is one of the most widely used European hardwoods in furniture and joinery. It has a pale pinkish-brown to light tan colour with a fine, even grain and smooth texture. It is a popular choice for fitted furniture, cabinetry, shelving and interior joinery where a consistent, attractive hardwood finish is required.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003cp\u003eThe 50mm width provides broader coverage, making it suitable for wider board edges, worktop edges, cabinet carcasses, furniture panels and surface work. Supplied in a 100m roll, it is ideal for workshop and production use where high volumes of edging are required from a single roll.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, display units, shopfitting, decorative trims and bespoke joinery work.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to enhance or adjust the natural beech colour to suit your project.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable substrate. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is Beech FSHM 50mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for wider cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat colour is beech veneer?\u003c\/h4\u003e\u003cp\u003eBeech veneer has a pale pinkish-brown to light tan colour with a fine, even grain and smooth texture.\u003c\/p\u003e\u003ch4\u003eIs the 50mm width suitable for wider board edges?\u003c\/h4\u003e\u003cp\u003eYes. The 50mm width is suitable for wider board edges, worktops, shelves, cabinet carcasses, doors and furniture panels.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can enhance or adjust the natural beech colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 50mm wide x 100m long flexible beech wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve beech furniture and panel edges, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849800765789,"sku":"VEN028B","price":37.05,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN028B_70308777-a825-4b39-8f41-b6a5543907bb.jpg?v=1781946635"},{"product_id":"maple-fs-unglued-flexible-wood-veneer-30mm-x-100m","title":"VENEER FSUG MAPLE 30x100m","description":"\u003cp\u003e\u003cstrong\u003eMaple Flexible Wood Veneer 30mm × 100m Unglued\u003c\/strong\u003e is a genuine real-wood edging roll for creating clean, natural-looking edges on furniture panels, cabinetry, shelving and bespoke interior joinery.\u003c\/p\u003e\u003cp\u003eMaple is prized for its pale cream colour, fine texture and smooth, understated grain. It provides a bright, contemporary alternative to darker or more heavily figured timbers and coordinates particularly well with Maple-veneered boards, light furniture surfaces and neutral interior finishes.\u003c\/p\u003e\u003cp\u003eThis veneer is supplied \u003cstrong\u003ewithout a factory-applied adhesive\u003c\/strong\u003e. The unglued construction gives furniture manufacturers and professional workshops control over the adhesive, application equipment and pressing method used for each substrate or production process.\u003c\/p\u003e\u003ch3\u003eWhy Choose Maple Veneer Edging?\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eGenuine natural Maple wood veneer\u003c\/li\u003e\n\u003cli\u003ePale cream colouring with a fine, consistent grain\u003c\/li\u003e\n\u003cli\u003e30mm width provides useful trimming allowance\u003c\/li\u003e\n\u003cli\u003eLong 100m roll for repeated workshop or production use\u003c\/li\u003e\n\u003cli\u003eUnglued for control over adhesive selection\u003c\/li\u003e\n\u003cli\u003eSuitable for straight and suitably shaped furniture edges\u003c\/li\u003e\n\u003cli\u003eCan be trimmed, lightly sanded and finished after bonding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eUseful 30mm Width\u003c\/h3\u003e\u003cp\u003eThe 30mm width provides greater coverage than standard narrow edging and leaves a generous trimming allowance on many common furniture panels. It is particularly useful where the board is wider than a standard 18mm panel, where an edge is slightly irregular, or where additional material is needed for accurate flush trimming.\u003c\/p\u003e\u003cp\u003eThe 100m roll is suitable for furniture workshops, cabinet manufacturers, shopfitters and joinery businesses carrying out repeated edging work.\u003c\/p\u003e\u003ch3\u003eUnglued Veneer for Controlled Bonding\u003c\/h3\u003e\u003cp\u003eThis FSUG Maple veneer does not have a hot-melt or pressure-sensitive adhesive backing. A compatible adhesive must therefore be selected according to the substrate, application machinery, production conditions and intended service environment.\u003c\/p\u003e\u003cp\u003eThe unglued format can be particularly useful for workshops using their own edge-banding adhesive system or requiring a bonding method designed for a specific board material.\u003c\/p\u003e\u003ch3\u003eApplication Guidance\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eStore the veneer in a clean, dry and stable workshop environment.\u003c\/li\u003e\n\u003cli\u003eAllow the veneer and panel material to acclimatise before application.\u003c\/li\u003e\n\u003cli\u003ePrepare a straight, clean, dry edge free from dust, oil and loose fibres.\u003c\/li\u003e\n\u003cli\u003eCut the veneer slightly longer than the finished component.\u003c\/li\u003e\n\u003cli\u003eApply a compatible adhesive following its manufacturer’s instructions.\u003c\/li\u003e\n\u003cli\u003ePosition the veneer accurately and apply firm, even pressure across its full width.\u003c\/li\u003e\n\u003cli\u003eAllow the bond to develop fully before trimming the excess material.\u003c\/li\u003e\n\u003cli\u003eTrim towards the panel face to reduce the risk of splitting the veneer.\u003c\/li\u003e\n\u003cli\u003eLightly finish the edge and apply a compatible coating where required.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eAlways carry out a test bond using the proposed substrate, adhesive, pressure and finishing system before beginning production.\u003c\/p\u003e\u003ch3\u003eFinishing Maple Veneer\u003c\/h3\u003e\u003cp\u003eThe real Maple surface can be finished with a compatible lacquer, oil, wax or stain. Clear finishes normally deepen the natural colour slightly, while stains can produce more noticeable changes because Maple has a close, fine grain.\u003c\/p\u003e\u003cp\u003eTest all finishing products on an offcut first. Avoid aggressive sanding, as decorative real-wood veneer is considerably thinner than solid timber.\u003c\/p\u003e\u003ch3\u003eNatural Wood Variation\u003c\/h3\u003e\u003cp\u003eMaple is a natural material, so colour, grain and markings may vary between rolls and production batches. These variations are normal and contribute to the genuine timber appearance of the finished edge.\u003c\/p\u003e\u003ch3\u003eTypical Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCabinet and cupboard edges\u003c\/li\u003e\n\u003cli\u003eShelving and bookcase components\u003c\/li\u003e\n\u003cli\u003eWardrobe and bedroom furniture\u003c\/li\u003e\n\u003cli\u003eDrawer fronts and furniture panels\u003c\/li\u003e\n\u003cli\u003eOffice and reception furniture\u003c\/li\u003e\n\u003cli\u003eRetail display fixtures\u003c\/li\u003e\n\u003cli\u003ePanel-edge repairs and refurbishment\u003c\/li\u003e\n\u003cli\u003eBespoke furniture and interior joinery\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStorage and Handling\u003c\/h3\u003e\u003cp\u003eKeep the veneer dry, clean and protected from direct sunlight, excessive heat and rapid humidity changes. Store the roll carefully to prevent crushing, creasing or damage to its edges.\u003c\/p\u003e\u003cp\u003eFor consistent results, bring the veneer, adhesive and substrate into the same working environment before bonding.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eIs this Maple veneer made from real wood?\u003c\/h4\u003e\u003cp\u003eYes. The visible surface is genuine natural Maple, so its colour and grain will vary slightly between rolls.\u003c\/p\u003e\u003ch4\u003eDoes the veneer have adhesive on the back?\u003c\/h4\u003e\u003cp\u003eNo. This is an unglued FSUG veneer. A suitable adhesive must be selected and applied separately.\u003c\/p\u003e\u003ch4\u003eWhat is the advantage of an unglued veneer?\u003c\/h4\u003e\u003cp\u003eUnglued veneer allows the workshop to choose an adhesive and pressing process suited to its substrate, machinery and production requirements.\u003c\/p\u003e\u003ch4\u003eWhat panel thickness is the 30mm width suitable for?\u003c\/h4\u003e\u003cp\u003eIt can be used on several panel thicknesses, provided the veneer is wider than the edge being covered. The excess material is trimmed flush after bonding.\u003c\/p\u003e\u003ch4\u003eCan Maple veneer be stained?\u003c\/h4\u003e\u003cp\u003eYes, but Maple can respond unevenly to some stains. Always test the selected stain and finishing system on an offcut first.\u003c\/p\u003e\u003cp\u003eBrowse our complete \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-veneer-edging\"\u003ereal wood veneer edging collection\u003c\/a\u003e, compare our \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-sheet-veneer\"\u003eflexible sheet veneers\u003c\/a\u003e, or visit the full \u003ca href=\"https:\/\/www.blum.org.uk\/pages\/veneers-edgings\"\u003eveneers and edgings range\u003c\/a\u003e.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849801650525,"sku":"VEN032E","price":17.93,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN032E.jpg?v=1784618897"},{"product_id":"oak-flexible-wood-veneer-fs-unglued-22mm-100m","title":"VENEER FS UNGLUED OAK 22x100m","description":"\u003cp\u003e\u003cstrong\u003eOak Flexible Wood Veneer FS Unglued 22mm × 100m\u003c\/strong\u003e is a genuine real-wood edging roll designed to provide exposed furniture-board edges with the warm colour, natural texture and distinctive grain of Oak.\u003c\/p\u003e\u003cp\u003eThe veneer is fleeced and sanded but supplied \u003cstrong\u003ewithout a factory-applied adhesive\u003c\/strong\u003e. This gives furniture manufacturers, cabinet makers and professional workshops complete control over the adhesive and bonding process used for their particular substrate, equipment and production requirements.\u003c\/p\u003e\u003cp\u003eAt 22mm wide, the edging is particularly suitable for common 18mm furniture panels because it leaves a small trimming allowance on both faces. The 100m roll supports repeated workshop and production use.\u003c\/p\u003e\u003ch3\u003eWhat Does FS Mean?\u003c\/h3\u003e\u003cp\u003eFS means \u003cstrong\u003eFleeced and Sanded\u003c\/strong\u003e. A supporting fleece improves the veneer’s flexibility and stability, while the natural Oak face is sanded to provide a smooth surface for finishing.\u003c\/p\u003e\u003cp\u003eUnlike FSHM veneer, this FS product does not include a hot-melt adhesive layer. A compatible adhesive must be selected and applied separately.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eGenuine natural Oak veneer surface\u003c\/li\u003e\n\u003cli\u003eFleeced backing for improved flexibility and stability\u003c\/li\u003e\n\u003cli\u003ePre-sanded real-wood face\u003c\/li\u003e\n\u003cli\u003eSupplied completely unglued\u003c\/li\u003e\n\u003cli\u003eAllows control over adhesive selection and application\u003c\/li\u003e\n\u003cli\u003e22mm width suited to many standard furniture panels\u003c\/li\u003e\n\u003cli\u003e100m roll for repeated workshop or production use\u003c\/li\u003e\n\u003cli\u003eCan be trimmed and finished after bonding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSuitable for Standard Panel Edges\u003c\/h3\u003e\u003cp\u003eThe 22mm width provides useful trimming allowance when applied to many 18mm MDF, chipboard, plywood and veneered furniture panels. Once bonded securely, the small overhang can be trimmed flush with the panel faces.\u003c\/p\u003e\u003cp\u003eAlways confirm that the substrate, adhesive and pressing method are compatible before beginning production.\u003c\/p\u003e\u003ch3\u003eWhy Choose Unglued Oak Veneer?\u003c\/h3\u003e\u003cp\u003eUnglued veneer gives the user flexibility to choose a bonding system appropriate for the substrate and manufacturing process. This can be useful for workshops operating an edge-banding machine, using a specialist woodworking adhesive or working with panels that require a particular bonding method.\u003c\/p\u003e\u003cp\u003eThe absence of a pre-applied adhesive also means the veneer is not restricted to one hot-melt formulation. Adhesive selection remains the responsibility of the installer.\u003c\/p\u003e\u003ch3\u003eApplication Guidance\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eAllow the veneer, adhesive and substrate to acclimatise in the same environment.\u003c\/li\u003e\n\u003cli\u003ePrepare a straight, stable, clean and dry panel edge.\u003c\/li\u003e\n\u003cli\u003eRemove dust, oil, grease and loose fibres that could weaken the bond.\u003c\/li\u003e\n\u003cli\u003eCut the veneer slightly longer than the finished component.\u003c\/li\u003e\n\u003cli\u003eSelect a compatible adhesive for the veneer, substrate and intended conditions.\u003c\/li\u003e\n\u003cli\u003eApply the adhesive according to its manufacturer’s coverage and open-time instructions.\u003c\/li\u003e\n\u003cli\u003ePosition the veneer with an even trimming allowance on both panel faces.\u003c\/li\u003e\n\u003cli\u003eApply firm, consistent pressure across the complete width and length.\u003c\/li\u003e\n\u003cli\u003eAllow the bond to develop fully before trimming or finishing.\u003c\/li\u003e\n\u003cli\u003eTrim towards the panel face to reduce the risk of splitting the natural veneer.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eAlways create a test piece using the intended substrate, adhesive, pressure and finishing system before beginning a complete production run.\u003c\/p\u003e\u003ch3\u003eFinishing Oak Veneer\u003c\/h3\u003e\u003cp\u003eOnce applied, the natural Oak surface can be finished with a compatible lacquer, oil, wax or stain. Clear finishes usually deepen the colour and emphasise the open grain, while stains can help coordinate the edging with surrounding furniture.\u003c\/p\u003e\u003cp\u003eTest the selected finish on an offcut first and avoid aggressive sanding, as decorative veneer is considerably thinner than solid Oak.\u003c\/p\u003e\u003ch3\u003eTypical Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCabinet and cupboard edging\u003c\/li\u003e\n\u003cli\u003eShelf edges\u003c\/li\u003e\n\u003cli\u003eWardrobe and bedroom furniture\u003c\/li\u003e\n\u003cli\u003eDrawer fronts and furniture components\u003c\/li\u003e\n\u003cli\u003eDoor and panel edges\u003c\/li\u003e\n\u003cli\u003eOffice and reception furniture\u003c\/li\u003e\n\u003cli\u003eRetail display and shopfitting units\u003c\/li\u003e\n\u003cli\u003eFurniture repairs and refurbishment\u003c\/li\u003e\n\u003cli\u003eBespoke interior joinery\u003c\/li\u003e\n\u003cli\u003eProduction edging with a separately selected adhesive\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eNatural Wood Variation\u003c\/h3\u003e\u003cp\u003eOak is a genuine natural material, so colour, grain, ray markings and other features will vary between rolls and batches. These variations are normal and help give the finished component an authentic real-timber appearance.\u003c\/p\u003e\u003ch3\u003eStorage and Handling\u003c\/h3\u003e\u003cp\u003eStore the roll in a clean, dry and stable environment, protected from direct sunlight, moisture, excessive heat and rapid changes in humidity. Keep the veneer supported and protect its edges from crushing or damage.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eIs this edging made from real Oak?\u003c\/h4\u003e\u003cp\u003eYes. The visible surface is genuine natural Oak veneer rather than a printed or imitation wood-effect material.\u003c\/p\u003e\u003ch4\u003eDoes this veneer have adhesive on the back?\u003c\/h4\u003e\u003cp\u003eNo. It is an unglued FS veneer. A compatible adhesive must be selected and applied separately.\u003c\/p\u003e\u003ch4\u003eWhat is the difference between FS and FSHM veneer?\u003c\/h4\u003e\u003cp\u003eFS veneer is fleeced and sanded but unglued. FSHM veneer is fleeced, sanded and supplied with a heat-activated hot-melt adhesive.\u003c\/p\u003e\u003ch4\u003eIs 22mm edging suitable for 18mm furniture board?\u003c\/h4\u003e\u003cp\u003eYes. It normally provides a small overhang on both faces of an 18mm panel, allowing it to be trimmed flush after bonding.\u003c\/p\u003e\u003ch4\u003eCan it be applied with an ordinary iron?\u003c\/h4\u003e\u003cp\u003eNo adhesive is present to activate with an iron. A separate compatible bonding system must first be selected and applied.\u003c\/p\u003e\u003ch4\u003eCan the Oak veneer be stained or oiled?\u003c\/h4\u003e\u003cp\u003eYes. It accepts many compatible wood stains, oils, lacquers and waxes. Test the selected finish first because it will alter the natural colour.\u003c\/p\u003e\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"Is this edging made from real Oak?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes. The visible surface is genuine natural Oak veneer rather than a printed wood-effect material.\"}},{\"@type\":\"Question\",\"name\":\"Does this Oak veneer have adhesive on the back?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No. It is an unglued FS veneer and requires a compatible adhesive to be selected and applied separately.\"}},{\"@type\":\"Question\",\"name\":\"What is the difference between FS and FSHM veneer?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"FS veneer is fleeced and sanded but unglued. FSHM veneer is fleeced, sanded and supplied with a heat-activated hot-melt adhesive.\"}},{\"@type\":\"Question\",\"name\":\"Is 22mm veneer edging suitable for 18mm board?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes. It normally leaves a small overhang on both faces of an 18mm panel so it can be trimmed flush after bonding.\"}},{\"@type\":\"Question\",\"name\":\"Can unglued Oak veneer edging be applied with an iron?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No adhesive is present to activate with an iron. A separate compatible bonding system must be selected and applied.\"}}]}\u003c\/script\u003e\u003cp\u003eBrowse our complete \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-veneer-edging\"\u003ereal wood veneer edging collection\u003c\/a\u003e, compare our \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-sheet-veneer\"\u003eflexible sheet veneers\u003c\/a\u003e, or explore the full \u003ca href=\"https:\/\/www.blum.org.uk\/pages\/veneers-edgings\"\u003eveneers and edgings range\u003c\/a\u003e.\u003c\/p\u003e","brand":"UNION VENEERS LTD","offers":[{"title":"Default Title","offer_id":62849802076509,"sku":"VEN033D","price":31.57,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN033D.jpg?v=1784618931"},{"product_id":"oak-flexible-wood-veneer-fs-unglued-30mm-100m","title":"VENEER FS UNGLUED OAK 30x100m","description":"\u003ch2\u003eOak Flexible Wood Veneer FS Unglued 30mm x 100m\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eOak Flexible Wood Veneer FS Unglued 30mm x 100m\u003c\/strong\u003e is a genuine real-wood edging roll designed for covering exposed furniture-board edges with the warm colour, natural texture and distinctive grain of oak.\u003c\/p\u003e\u003cp\u003eThe veneer is fleeced and sanded but supplied completely unglued. This allows cabinet makers, furniture manufacturers and professional workshops to select an adhesive suited to their particular substrate, production equipment and installation method.\u003c\/p\u003e\u003cp\u003eUnlike printed or imitation wood-effect edging, the visible surface is genuine oak veneer. Once correctly applied and finished, it creates an authentic timber appearance that coordinates particularly well with oak-faced MDF, chipboard, plywood and solid-oak furniture components.\u003c\/p\u003e\u003ch3\u003eWhat Does FS Mean?\u003c\/h3\u003e\u003cp\u003eFS stands for \u003cstrong\u003eFleeced and Sanded\u003c\/strong\u003e. A supporting fleece improves the flexibility and stability of the veneer, while the natural oak face is sanded to provide a smooth surface ready for final preparation and finishing.\u003c\/p\u003e\u003cp\u003eThis FS version does not have a heat-activated adhesive coating. A compatible adhesive must be selected and applied separately. This is the principal difference between FS unglued veneer and FSHM pre-glued veneer.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eGenuine natural oak veneer surface\u003c\/li\u003e\n\u003cli\u003eFleeced backing for improved flexibility and stability\u003c\/li\u003e\n\u003cli\u003eSmooth, sanded wood face\u003c\/li\u003e\n\u003cli\u003eSupplied without pre-applied adhesive\u003c\/li\u003e\n\u003cli\u003eAllows control over adhesive selection and application\u003c\/li\u003e\n\u003cli\u003e30mm width for wider edges and generous trimming allowance\u003c\/li\u003e\n\u003cli\u003eLong 100m roll for workshop and production use\u003c\/li\u003e\n\u003cli\u003eCan be trimmed, lightly sanded, stained and finished after bonding\u003c\/li\u003e\n\u003cli\u003eSuitable for furniture manufacture, refurbishment and bespoke joinery\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSuitable Applications\u003c\/h3\u003e\u003cp\u003eThe 30mm width provides useful additional coverage for wider or thicker panels and applications requiring a generous trimming allowance. Typical uses include:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCabinet and cupboard edging\u003c\/li\u003e\n\u003cli\u003eShelf and worktop edges\u003c\/li\u003e\n\u003cli\u003eWardrobe and bedroom furniture\u003c\/li\u003e\n\u003cli\u003eDrawer fronts and furniture components\u003c\/li\u003e\n\u003cli\u003eDoor and panel edges\u003c\/li\u003e\n\u003cli\u003eOak-faced MDF, plywood and chipboard\u003c\/li\u003e\n\u003cli\u003eOffice and reception furniture\u003c\/li\u003e\n\u003cli\u003eRetail displays and shopfitting\u003c\/li\u003e\n\u003cli\u003eFurniture repairs and restoration\u003c\/li\u003e\n\u003cli\u003eBespoke interior joinery\u003c\/li\u003e\n\u003cli\u003eProduction edging using a separately selected adhesive\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eApplication Guidance\u003c\/h3\u003e\u003cp\u003ePrepare a straight, clean, dry and stable panel edge, removing dust, oil, grease and loose fibres that could weaken the bond.\u003c\/p\u003e\u003cp\u003eSelect an adhesive compatible with both the veneer backing and the substrate. Follow the adhesive manufacturer’s instructions regarding coverage, open time, pressure and curing time.\u003c\/p\u003e\u003cp\u003ePosition the veneer with sufficient material extending beyond both faces of the panel. Apply firm, consistent pressure across the complete width and length. Allow the adhesive to develop fully before trimming the veneer flush.\u003c\/p\u003e\u003cp\u003eAlways produce a test piece using the intended substrate, adhesive and finishing system before beginning a full production run.\u003c\/p\u003e\u003ch3\u003eFinishing the Veneer\u003c\/h3\u003e\u003cp\u003eOnce bonded and trimmed, the natural oak surface can be finished with a compatible lacquer, oil, wax or wood stain. Clear finishes normally deepen the colour and highlight the characteristic oak grain, while stains can help coordinate the edging with surrounding furniture.\u003c\/p\u003e\u003cp\u003eBecause decorative veneer is considerably thinner than solid timber, sand carefully and test the selected finish on an offcut first.\u003c\/p\u003e\u003ch3\u003eNatural Wood Variation\u003c\/h3\u003e\u003cp\u003eOak is a natural material. Differences in shade, grain direction, ray markings and figure should be expected between sections and production batches. These variations are normal and contribute to the authentic appearance of the finished furniture.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eDoes this veneer have glue on the back?\u003c\/h4\u003e\u003cp\u003eNo. It is supplied completely unglued, allowing you to select an adhesive suitable for your substrate and application process.\u003c\/p\u003e\u003ch4\u003eWhat is the difference between FS and FSHM veneer?\u003c\/h4\u003e\u003cp\u003eFS veneer is fleeced and sanded but unglued. FSHM veneer includes a factory-applied heat-activated hot-melt adhesive.\u003c\/p\u003e\u003ch4\u003eCan this veneer be applied with an ordinary iron?\u003c\/h4\u003e\u003cp\u003eNot on its own. There is no adhesive coating for an iron to activate. A separate compatible bonding system must be selected and applied.\u003c\/p\u003e\u003ch4\u003eCan the oak veneer be stained or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, it can accept many compatible stains, oils, waxes and lacquers. Always test the finish on an offcut first.\u003c\/p\u003e\u003ch4\u003eWhy choose the 30mm width?\u003c\/h4\u003e\u003cp\u003eThe wider strip provides additional coverage for thicker board edges and gives a generous trimming allowance when a flush finished edge is required.\u003c\/p\u003e\u003cp\u003eBrowse our complete \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-veneer-edging\"\u003ereal wood veneer edging collection\u003c\/a\u003e, compare our \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-sheet-veneer\"\u003eflexible sheet veneers\u003c\/a\u003e, or explore the full \u003ca href=\"https:\/\/www.blum.org.uk\/pages\/veneers-edgings\"\u003eveneers and edgings range\u003c\/a\u003e.\u003c\/p\u003e","brand":"UNION VENEERS LTD","offers":[{"title":"Default Title","offer_id":62849802371421,"sku":"VEN033E","price":31.57,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN033E_96459c2c-94f9-44ff-b6b5-9a4fd2281e1e.jpg?v=1784619230"},{"product_id":"white-oak-flexible-wood-veneer-fs-unglued-50mm-300m","title":"VENEER FS UNGLUED W\/OAK 50x300m","description":"\u003cp\u003e\u003cstrong\u003eWhite Oak Flexible Wood Veneer FS Unglued 50mm × 300m\u003c\/strong\u003e is a genuine real-wood edging roll designed for high-volume production workshops and furniture manufacturers requiring a wide, long-run supply of unglued Oak veneer edging.\u003c\/p\u003e\u003cp\u003eThe veneer is fleeced and sanded but supplied \u003cstrong\u003ewithout a factory-applied adhesive\u003c\/strong\u003e, giving workshops complete control over the bonding method and adhesive choice to suit their substrate, machinery and production process.\u003c\/p\u003e\u003cp\u003eWhite Oak offers a \u003cstrong\u003epale, clean tone with a fine, straight grain\u003c\/strong\u003e — a lighter and more contemporary alternative to traditional European Oak, well suited to modern cabinetry, Scandinavian-style furniture and neutral interior schemes. The 50mm width provides generous coverage for wider panels, door edges, worktop details and components where standard narrow edging is insufficient. The 300m roll minimises changeovers in production environments.\u003c\/p\u003e\u003ch3\u003eWhat Does FS Mean?\u003c\/h3\u003e\u003cp\u003eFS means \u003cstrong\u003eFleeced and Sanded\u003c\/strong\u003e. A supporting fleece improves the veneer’s flexibility and stability, while the natural White Oak face is sanded to provide a smooth surface for finishing. Unlike FSHM veneer, this FS product has no hot-melt adhesive — a compatible adhesive must be selected and applied separately.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eGenuine natural White Oak veneer surface\u003c\/li\u003e\n\u003cli\u003ePale, clean tone with fine straight grain\u003c\/li\u003e\n\u003cli\u003eFleeced backing for improved flexibility and stability\u003c\/li\u003e\n\u003cli\u003ePre-sanded real-wood face\u003c\/li\u003e\n\u003cli\u003eSupplied completely unglued\u003c\/li\u003e\n\u003cli\u003eFull control over adhesive selection and application\u003c\/li\u003e\n\u003cli\u003eWide 50mm format for deeper components and generous trimming allowance\u003c\/li\u003e\n\u003cli\u003eLong 300m production roll to minimise changeovers\u003c\/li\u003e\n\u003cli\u003eCan be trimmed and finished after bonding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eTypical Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWide cabinet and cupboard edging\u003c\/li\u003e\n\u003cli\u003eDoor and frame edges\u003c\/li\u003e\n\u003cli\u003eWorktop and counter details\u003c\/li\u003e\n\u003cli\u003eThick shelving and deep panel edging\u003c\/li\u003e\n\u003cli\u003eWardrobe and bedroom furniture\u003c\/li\u003e\n\u003cli\u003eOffice and reception furniture\u003c\/li\u003e\n\u003cli\u003eRetail display and shopfitting\u003c\/li\u003e\n\u003cli\u003eFurniture repairs and refurbishment\u003c\/li\u003e\n\u003cli\u003eBespoke interior joinery\u003c\/li\u003e\n\u003cli\u003eHigh-volume production edging runs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eApplication Guidance\u003c\/h3\u003e\u003cp\u003ePrepare a straight, clean, dry and stable panel edge. Select a compatible adhesive for the veneer, substrate and intended conditions. Apply firm, consistent pressure across the complete width and length. Allow the bond to develop fully before trimming. Always test on an offcut before beginning a production run.\u003c\/p\u003e\u003ch3\u003eNatural Wood Variation\u003c\/h3\u003e\u003cp\u003eWhite Oak is a natural material, so colour, grain and markings will vary between rolls and batches. These variations are normal and contribute to an authentic timber appearance.\u003c\/p\u003e\u003ch3\u003eStorage and Handling\u003c\/h3\u003e\u003cp\u003eStore the roll in a clean, dry and stable environment, protected from direct sunlight, moisture, excessive heat and rapid humidity changes. Keep the veneer supported and protect its edges from crushing or damage.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eIs this edging made from real White Oak?\u003c\/h4\u003e\u003cp\u003eYes. The visible surface is genuine natural White Oak veneer.\u003c\/p\u003e\u003ch4\u003eDoes this veneer have adhesive on the back?\u003c\/h4\u003e\u003cp\u003eNo. It is an unglued FS veneer. A compatible adhesive must be selected and applied separately.\u003c\/p\u003e\u003ch4\u003eWhy choose 50mm width?\u003c\/h4\u003e\u003cp\u003eThe 50mm width covers deeper furniture components, broad edges and repair areas that cannot be finished with standard narrow edge banding.\u003c\/p\u003e\u003ch4\u003eWhat is the advantage of the 300m roll?\u003c\/h4\u003e\u003cp\u003eThe long roll reduces changeover frequency in production environments, improving efficiency and reducing waste.\u003c\/p\u003e\u003ch4\u003eCan the White Oak veneer be stained or finished?\u003c\/h4\u003e\u003cp\u003eYes. It accepts compatible lacquers, oils, waxes and stains. Always test the selected finish on an offcut first.\u003c\/p\u003e\u003cp\u003eBrowse our complete \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-veneer-edging\"\u003ereal wood veneer edging collection\u003c\/a\u003e, compare our \u003ca href=\"https:\/\/www.blum.org.uk\/collections\/veneers-edgings-sheet-veneer\"\u003eflexible sheet veneers\u003c\/a\u003e, or explore the full \u003ca href=\"https:\/\/www.blum.org.uk\/pages\/veneers-edgings\"\u003eveneers and edgings range\u003c\/a\u003e.\u003c\/p\u003e","brand":"SMC WHOLESALE","offers":[{"title":"Default Title","offer_id":62849802436957,"sku":"VEN033F","price":174.08,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN033F.jpg?v=1784619230"},{"product_id":"american-black-walnut-fshm-flexible-wood-veneer-25mm-x-100m","title":"VENEER FSHM WALNUT\/USA BLK 25x100m","description":"\u003ch2\u003eAmerican Black Walnut Flexible Wood Veneer FSHM 25mm x 100m\u003c\/h2\u003e\u003cp\u003eAmerican Black Walnut Flexible Wood Veneer FSHM 25mm x 100m is a narrow real wood veneer roll designed for cabinet edging, furniture repairs, shelf edges, doors, trims and decorative joinery work.\u003c\/p\u003e\u003cp\u003eAmerican black walnut, also known as USA black walnut, is a premium decorative timber finish valued for its rich brown colour, natural grain and high-quality furniture appearance. It is widely used in cabinet making, fitted furniture, restoration work and bespoke interior joinery where a darker hardwood finish is required.\u003c\/p\u003e\u003cp\u003eThe 25mm width makes this veneer ideal for slightly wider board edges, cabinet parts, shelving edges, drawer fronts, doors, trims and repair sections. Supplied in a longer 100m roll, it is well suited to workshop use, repeat edging work and production applications where a continuous walnut veneer strip is required.\u003c\/p\u003e\u003cp\u003eThis flexible walnut veneer can be used to upgrade plain board edges, match existing walnut-effect furniture, repair worn edging or add a real wood finish to decorative panels and fitted furniture.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, shelving, drawer fronts, door edges, display units, shopfitting, decorative trims, panel finishing and bespoke joinery manufacture.\u003c\/p\u003e\u003cp\u003eOnce applied, this veneer edging accepts stain, lacquer, wax and oil finishes, allowing you to match or enhance the natural walnut colour to suit your project requirements.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is American Black Walnut FSHM 25mm veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for cabinet edging, furniture repairs, shelf edges, drawer fronts, door edges, trims and decorative joinery work.\u003c\/p\u003e\u003ch4\u003eWhat does WALNUT\/USA BLK mean?\u003c\/h4\u003e\u003cp\u003eIt refers to USA Black Walnut, commonly known as American Black Walnut.\u003c\/p\u003e\u003ch4\u003eIs the 25mm width suitable for cabinet edging?\u003c\/h4\u003e\u003cp\u003eYes. The 25mm width is suitable for board edges, shelves, cabinet parts, doors and furniture details.\u003c\/p\u003e\u003ch4\u003eCan it be stained, lacquered, waxed or oiled?\u003c\/h4\u003e\u003cp\u003eYes. Once applied, this veneer edging accepts stain, lacquer, wax and oil finishes, so you can match or enhance the natural walnut colour to suit your project.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 25mm wide x 100m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used for furniture restoration?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to restore or improve walnut-effect furniture, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849803845981,"sku":"VEN041A","price":41.76,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN041A_214dd681-64fe-4d8c-b3ff-f1a3c89772ad.jpg?v=1788793713"},{"product_id":"american-black-walnut-fshm-flexible-wood-veneer-30mm-x-100m","title":"American Black Walnut Flexible Wood Veneer FSHM 30mm x 100m","description":"\u003cp\u003eAmerican Black Walnut Flexible Wood Veneer FSHM 30mm × 100m is a genuine real-wood veneer edging roll with a factory-applied heat-activated adhesive. It provides an efficient way to create a rich natural walnut finish on furniture, cabinetry, shelving and interior joinery.\u003c\/p\u003e\u003cp\u003eAmerican black walnut is valued for its deep brown colouring and attractive natural grain. Its appearance can range from warm dark tan to rich chocolate brown, with both straight and decorative grain patterns occurring throughout the veneer.\u003c\/p\u003e\u003cp\u003eThe 30mm width provides additional coverage for wider board edges, thicker panels and applications where extra trimming allowance is required. Supplied in a generous 100m roll, it is suitable for professional workshops, repeated edging work and furniture-production applications.\u003c\/p\u003e\u003cp\u003eThe veneer is supplied unfinished and sanded smooth. Once applied, it can be trimmed, lightly sanded and coated with a compatible lacquer, oil, wax or clear protective finish.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eGenuine American black walnut veneer\u003c\/li\u003e\n\u003cli\u003eFSHM flexible construction\u003c\/li\u003e\n\u003cli\u003ePre-applied hot-melt adhesive\u003c\/li\u003e\n\u003cli\u003eHeat-activated application\u003c\/li\u003e\n\u003cli\u003eSmooth sanded unfinished surface\u003c\/li\u003e\n\u003cli\u003eRich dark-brown natural appearance\u003c\/li\u003e\n\u003cli\u003e30mm width\u003c\/li\u003e\n\u003cli\u003e100m roll length\u003c\/li\u003e\n\u003cli\u003eSuitable for furniture and cabinet edging\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eApplication guidance\u003c\/h3\u003e\u003cp\u003eApply to a clean, dry, smooth and stable surface. Position the veneer accurately and activate the adhesive using suitable edge-banding equipment, a veneer iron or another controlled heat source. Apply firm, even pressure while warm and allow the bond to cool before trimming.\u003c\/p\u003e\u003cp\u003eNatural colour and grain variation should be expected throughout the roll.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849803878749,"sku":"VEN041B","price":51.72,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/american-black-walnut-fshm-pre-glued-veneer-22mm-100m-ven041.png?v=1784628137"},{"product_id":"american-black-walnut-fshm-flexible-wood-veneer-50mm-x-50m","title":"VENEER FSHM WALNUT\/USA BLK 50x50m","description":"\u003ch2\u003eAmerican Black Walnut Flexible Wood Veneer FSHM 50mm x 50m\u003c\/h2\u003e\u003cp\u003eAmerican Black Walnut Flexible Wood Veneer FSHM 50mm x 50m is a premium decorative veneer roll for cabinet makers, furniture makers, joiners and restoration work where a rich dark walnut finish is required.\u003c\/p\u003e\u003cp\u003eAmerican black walnut is highly valued for its deep brown colouring, attractive grain and luxury hardwood appearance. The heartwood can range from dark tan through to deep chocolate brown, with grain patterns varying from straight to more decorative figuring depending on the cut and natural timber character.\u003c\/p\u003e\u003cp\u003eThis 50mm wide veneer roll is particularly useful for edging, trimming, repairs and detail work where a narrow, continuous walnut strip is needed. It is suitable for finishing cabinet edges, furniture panels, doors, shelves, display units, fitted furniture and bespoke joinery projects.\u003c\/p\u003e\u003cp\u003eThe 50m roll length makes it practical for workshop use, allowing multiple panels, edges or repair sections to be finished from one roll. It is ideal for matching walnut-effect surfaces, upgrading plain board edges or adding a real wood appearance to furniture and interior joinery.\u003c\/p\u003e\u003cp\u003eSuitable applications include cabinet edging, furniture restoration, decorative panel work, door edging, shelving, shopfitting, joinery repairs and bespoke furniture manufacture.\u003c\/p\u003e\u003cp\u003eFor best results, apply to a clean, dry, flat and stable surface using a suitable veneer adhesive or workshop bonding method. Always check grain direction, surface preparation and adhesive compatibility before final application.\u003c\/p\u003e\u003cp\u003eAmerican black walnut is commonly associated with dark tan to deep chocolate heartwood, and the grain can vary from very straight to more figured patterns. Flat-cut walnut veneer can produce a cathedral grain pattern, while quarter-cut veneer is usually straighter and more even.\u003c\/p\u003e\u003ch3\u003eWhat Does FSHM Mean?\u003c\/h3\u003e\u003cp\u003eFSHM stands for \u003cstrong\u003eFleeced, Sanded and Hot Melt\u003c\/strong\u003e. The back of the veneer is fleeced for flexibility and stability, the front face is sanded to a smooth, consistent finish, and a hot melt glue is applied to the reverse for iron-on application. When you trim the edging after application, \u003cstrong\u003ethe cut follows the blade rather than the grain\u003c\/strong\u003e — giving you a clean, controlled trim line regardless of grain direction.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003ch4\u003eWhat is American Black Walnut FSHM veneer used for?\u003c\/h4\u003e\u003cp\u003eIt is used for decorative edging, cabinet work, furniture restoration, shelving, doors, panel finishing and joinery repairs.\u003c\/p\u003e\u003ch4\u003eIs this suitable for cabinet edging?\u003c\/h4\u003e\u003cp\u003eYes. The 50mm width makes it suitable for cabinet edges, board edges, shelves and other narrow decorative finishing work.\u003c\/p\u003e\u003ch4\u003eWhat colour is American black walnut veneer?\u003c\/h4\u003e\u003cp\u003eAmerican black walnut usually has a rich brown appearance, ranging from dark tan to deep chocolate tones, with natural variation in grain and figure.\u003c\/p\u003e\u003ch4\u003eWhat size is this veneer roll?\u003c\/h4\u003e\u003cp\u003eThis listing is for a 50mm wide x 50m long flexible wood veneer roll.\u003c\/p\u003e\u003ch4\u003eCan it be used on furniture repairs?\u003c\/h4\u003e\u003cp\u003eYes. It can be used to repair, restore or improve walnut-effect furniture, provided the surface is clean, dry, stable and suitable for veneer bonding.\u003c\/p\u003e","brand":"MERENDA LTD","offers":[{"title":"Default Title","offer_id":62849803911517,"sku":"VEN041C","price":41.76,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/4100\/7453\/files\/VEN041C_d3dcbebb-caba-4500-946e-b5cd1b10306b.jpg?v=1788794354"}],"url":"https:\/\/www.blum.org.uk\/collections\/real-wood-veneer-edging-rolls.oembed","provider":"Hart Wholesale","version":"1.0","type":"link"}